* Please Contact Us for Current Pricing!
Stone Countertop Spray Cleaner
For daily cleaning, without leaving streaks. No buffing required.
Specifically developed for fast and safe daily cleaning and effectively removing grease and other dirt's, while enhancing the characteristics of the stone.
Never use abrasives, vinegar or other inappropriate cleaning agents on natural stone surfaces!
Application For granite, marble, travertin, limestone and other natural stone, but also synthetic surfaces.
Directions Turn nozzle to "open"
Spray HG on the surface to be cleaned, then wipe with clean, maybe dampened cloth.
In case of stubborn dirt, spray and leave to activate for a few minutes, then wipe with cloth or possibly HG Kitchen Sponge.
Afterwards gently wipe with clean cloth or papertowel.
After use turn nozzle to "CLOSE".
Product Information Colour : Colourless, pleasantly scented pH : 7 relative density : 0.995 g/ml (20C/68F)
Caution Do NOT spray ditectly on food.
Keep out of reach for children.
For daily cleaning, without leaving streaks. No buffing required.
Specifically developed for fast and safe daily cleaning and effectively removing grease and other dirt's, while enhancing the characteristics of the stone.
Never use abrasives, vinegar or other inappropriate cleaning agents on natural stone surfaces!
Application For granite, marble, travertin, limestone and other natural stone, but also synthetic surfaces.
Directions Turn nozzle to "open"
Spray HG on the surface to be cleaned, then wipe with clean, maybe dampened cloth.
In case of stubborn dirt, spray and leave to activate for a few minutes, then wipe with cloth or possibly HG Kitchen Sponge.
Afterwards gently wipe with clean cloth or papertowel.
After use turn nozzle to "CLOSE".
Product Information Colour : Colourless, pleasantly scented pH : 7 relative density : 0.995 g/ml (20C/68F)
Caution Do NOT spray ditectly on food.
Keep out of reach for children.
Stone Countertop Penetrating Sealer
DEFENDER protective sealer, solventbased.
Virtually invisible protective penetrating sealer to block stains and dirt, without changing the colour and gloss.
LVP-VOC compliant, solvent based sealer, for interior and exterior use.
Application Suitable for all natural stones, pavers, brick, even concrete surfaces.
Directions Shake can well before use. Wear goggles & rubber gloves, and ensure adequate ventilation. Protect surfaces NOT to be treated. Ensure that surface to be treated are clean and completely dry.
Smaller area: pour some sealer on lintfree cloth and wipe over surface to be treated. Allow to penetrate for 10-15 minutes before wiping up any puddles or surplus.
Allow to dry for 2 hours before applying a second coat, following same instructions.
Larger areas: pour sealer in paint tray and apply thin coat of sealer with hair (not foam) roller, in one direction. After 10-15 minutes remove any puddles or surplus with lintfree cloth or squeegee.
Allow to dry for 2 hours before applying a second following same directions.
After final coat, allow to dry minimum 4 hours before walking, and minimum 12 hours before heavier traffic.
Product Information s.g. : 0.88 compositions : petroleum distillate & blend of proprietary polymers. usage : 200-400 sq/ft per litre.
Caution Combustible liquid. Wear goggles and rubber gloves. Ensure adequate ventilation.
Do not MIX or match with other products to avoid result differences. Best working temperature are between 15-25C / 55-75F, low humidity and never in full sun.
Avoid dust and dirt while drying. For outside applications, ensure sprinkler systems to be shut off, and avoid any moisture and rain during drying process.
DEFENDER protective sealer, solventbased.
Virtually invisible protective penetrating sealer to block stains and dirt, without changing the colour and gloss.
LVP-VOC compliant, solvent based sealer, for interior and exterior use.
Application Suitable for all natural stones, pavers, brick, even concrete surfaces.
Directions Shake can well before use. Wear goggles & rubber gloves, and ensure adequate ventilation. Protect surfaces NOT to be treated. Ensure that surface to be treated are clean and completely dry.
Smaller area: pour some sealer on lintfree cloth and wipe over surface to be treated. Allow to penetrate for 10-15 minutes before wiping up any puddles or surplus.
Allow to dry for 2 hours before applying a second coat, following same instructions.
Larger areas: pour sealer in paint tray and apply thin coat of sealer with hair (not foam) roller, in one direction. After 10-15 minutes remove any puddles or surplus with lintfree cloth or squeegee.
Allow to dry for 2 hours before applying a second following same directions.
After final coat, allow to dry minimum 4 hours before walking, and minimum 12 hours before heavier traffic.
Product Information s.g. : 0.88 compositions : petroleum distillate & blend of proprietary polymers. usage : 200-400 sq/ft per litre.
Caution Combustible liquid. Wear goggles and rubber gloves. Ensure adequate ventilation.
Do not MIX or match with other products to avoid result differences. Best working temperature are between 15-25C / 55-75F, low humidity and never in full sun.
Avoid dust and dirt while drying. For outside applications, ensure sprinkler systems to be shut off, and avoid any moisture and rain during drying process.
Stone & Marble Protector - VOC FREE
Stone & Marble Protector is a waterbased, and completely VOC-FREE penetrating sealer for medium to very absorptive surfaces.
Completely invisible and No-Scent.
Protects surface from staining and reduces the chances of efflorescence, frost damage, mould and algae, and protects extremely well from oil, fat and grease staining.
Attention: This waterbased product may NOT be mixed with other and/or solventbased penetrating sealers. To avoid possible colour differences, do NOT use this product adjacent other penetrating sealers. This product may be used overtop fully dried solventbased penetrating sealers, to further protect from dirt.
Application This product is ideal for low-absorptive natural stones, like Granite, polished marble, but also limestone and travertine as well as fullbody porcelain.
Directions The surface must be clean and completely dry.
Apply the liquid generously, in straight strokes and in one direction, with brush or mohair roller. Always work from top to bottom. Do NOT treat more than 60-80 sq/ft at a time to ensure being able to follow instructions.
Allow liquid to penetrate for no longer than 10 minutes, before removing any surplus with clean cloth, or squeegee surplus off to untreated area. If there is no surplus apply a subsequent coat, allowing 1 hour drying time. When a surplus is still present, remove within 10 minutes from application. This also means that the surface is saturated and no subsequent coates are needed.
Allow surface to dry for 3 hours before any foot traffic or 12 hours before other traffic, after 24 hours the surface is fully protected and may be cleaned.
Coverage: 50-100 sq/ft per 250 ml.but strongly depending absorption. ( 1000 - 2000 sq/ft per 5 Litre.)
Product Information Relative Density : 1.006 g/ml. pH : 4.2
: waterbased colour : clear liquid.
Caution Keep out of reach for children. Keep from Freezing. If swallowed, call a Poison Control Centre or doctor immediately. Do NOT induce vomiting.
Stone & Marble Protector is a waterbased, and completely VOC-FREE penetrating sealer for medium to very absorptive surfaces.
Completely invisible and No-Scent.
Protects surface from staining and reduces the chances of efflorescence, frost damage, mould and algae, and protects extremely well from oil, fat and grease staining.
Attention: This waterbased product may NOT be mixed with other and/or solventbased penetrating sealers. To avoid possible colour differences, do NOT use this product adjacent other penetrating sealers. This product may be used overtop fully dried solventbased penetrating sealers, to further protect from dirt.
Application This product is ideal for low-absorptive natural stones, like Granite, polished marble, but also limestone and travertine as well as fullbody porcelain.
Directions The surface must be clean and completely dry.
Apply the liquid generously, in straight strokes and in one direction, with brush or mohair roller. Always work from top to bottom. Do NOT treat more than 60-80 sq/ft at a time to ensure being able to follow instructions.
Allow liquid to penetrate for no longer than 10 minutes, before removing any surplus with clean cloth, or squeegee surplus off to untreated area. If there is no surplus apply a subsequent coat, allowing 1 hour drying time. When a surplus is still present, remove within 10 minutes from application. This also means that the surface is saturated and no subsequent coates are needed.
Allow surface to dry for 3 hours before any foot traffic or 12 hours before other traffic, after 24 hours the surface is fully protected and may be cleaned.
Coverage: 50-100 sq/ft per 250 ml.but strongly depending absorption. ( 1000 - 2000 sq/ft per 5 Litre.)
Product Information Relative Density : 1.006 g/ml. pH : 4.2
: waterbased colour : clear liquid.
Caution Keep out of reach for children. Keep from Freezing. If swallowed, call a Poison Control Centre or doctor immediately. Do NOT induce vomiting.
Stone Countertop Top Penetrating Sealer
Top Protector, waterbased sealer for marble & granite
Odourless, invisible protection and dirt delaying action, particularly against (edible) oils, vegetable and animal fats, and other kinds of dirt. The best protection can be achieved by applying HG Top Protector overtop of other solventbased penetrating sealers, like HG Impregnator, HG Marble Impregnator, or Colour Enhancer. Does not change the colour of the stone. For interior / exterior use.
Application Ideal on most absorptive surfaces, like marble, travertine, limestone, slate, sandstone but also granite. Great for countertops.
Directions Ensure that the surface is clean, free from dust, dirt's and residues from cleaners, and completely dry. Clean existing surfaces with HG Marble Stripper prior to application.
Apply with a lint-free cloth (enclosed). The products tends to contract and must therefore be rubbed thoroughly into the entire surface for about 30 seconds. Do NOT treat more than 5 sq/ft at a time. On highly porous surfaces a brush may be used. After 2 hours a second coat may be applied. Allow 24 hours to dry completely and before spilling liquids or cleaning.
Product Information usage : 100 ml. for up to 10m2 /100 sq/ft (depending absorption.) s.g : 0.99 g/ml flashpoint : approx. 34C compositions: : solvents and fluorcarbons.
Caution Poisonous in liquid form only, safe once dried.
Highly flammable. Do not smoke while applying.
Keep out of reach for children. Keep from freezing.
In case of contact with eyes, rinse for 15 minutes, with clean water, and consult phycisian. In case of swallowing, seek medical advice immediately.
Top Protector, waterbased sealer for marble & granite
Odourless, invisible protection and dirt delaying action, particularly against (edible) oils, vegetable and animal fats, and other kinds of dirt. The best protection can be achieved by applying HG Top Protector overtop of other solventbased penetrating sealers, like HG Impregnator, HG Marble Impregnator, or Colour Enhancer. Does not change the colour of the stone. For interior / exterior use.
Application Ideal on most absorptive surfaces, like marble, travertine, limestone, slate, sandstone but also granite. Great for countertops.
Directions Ensure that the surface is clean, free from dust, dirt's and residues from cleaners, and completely dry. Clean existing surfaces with HG Marble Stripper prior to application.
Apply with a lint-free cloth (enclosed). The products tends to contract and must therefore be rubbed thoroughly into the entire surface for about 30 seconds. Do NOT treat more than 5 sq/ft at a time. On highly porous surfaces a brush may be used. After 2 hours a second coat may be applied. Allow 24 hours to dry completely and before spilling liquids or cleaning.
Product Information usage : 100 ml. for up to 10m2 /100 sq/ft (depending absorption.) s.g : 0.99 g/ml flashpoint : approx. 34C compositions: : solvents and fluorcarbons.
Caution Poisonous in liquid form only, safe once dried.
Highly flammable. Do not smoke while applying.
Keep out of reach for children. Keep from freezing.
In case of contact with eyes, rinse for 15 minutes, with clean water, and consult phycisian. In case of swallowing, seek medical advice immediately.
Marble Polish
a waterbased polish, ideal for smaller surfaces, table tops, windows sills, tresholds, work tops and counter tops.
Easy and quick to apply, and leaves a beautiful sheen. Also enhances the coulour and structures of stones.
Application Best suitable for smaller surfaces of marble, travertine, granite and other natural stones, as well as some synthetic surfaces.
Directions Ensure that the surface to be treated is clean and completely dry. Clean dirty surfaces with HG Marble Stripper.
Leave surface after cleaning to dry for up to 24 hours to avoid staining of the surface.
Apply thinly with lint-free cloth.
Allow the polish to dry for up to 30 minutes, before polishing with clean, dry and lint-free cloth, in circular motions, until a gloss appears.
Product Information s.g : 0.997 g/ml conteint : methylchloroisothiazolinone pH : 9.1 VOC : 15 gr/L or 1.5 %
Caution Keep out of reach for children.
Keep from freezing.
a waterbased polish, ideal for smaller surfaces, table tops, windows sills, tresholds, work tops and counter tops.
Easy and quick to apply, and leaves a beautiful sheen. Also enhances the coulour and structures of stones.
Application Best suitable for smaller surfaces of marble, travertine, granite and other natural stones, as well as some synthetic surfaces.
Directions Ensure that the surface to be treated is clean and completely dry. Clean dirty surfaces with HG Marble Stripper.
Leave surface after cleaning to dry for up to 24 hours to avoid staining of the surface.
Apply thinly with lint-free cloth.
Allow the polish to dry for up to 30 minutes, before polishing with clean, dry and lint-free cloth, in circular motions, until a gloss appears.
Product Information s.g : 0.997 g/ml conteint : methylchloroisothiazolinone pH : 9.1 VOC : 15 gr/L or 1.5 %
Caution Keep out of reach for children.
Keep from freezing.
Marble Polish
a waterbased polish, ideal for smaller surfaces, table tops, windows sills, tresholds, work tops and counter tops.
Easy and quick to apply, and leaves a beautiful sheen. Also enhances the coulour and structures of stones.
Application Best suitable for smaller surfaces of marble, travertine, granite and other natural stones, as well as some synthetic surfaces.
Directions Ensure that the surface to be treated is clean and completely dry. Clean dirty surfaces with HG Marble Stripper.
Leave surface after cleaning to dry for up to 24 hours to avoid staining of the surface.
Apply thinly with lint-free cloth.
Allow the polish to dry for up to 30 minutes, before polishing with clean, dry and lint-free cloth, in circular motions, until a gloss appears.
Product Information s.g : 0.997 g/ml conteint : methylchloroisothiazolinone pH : 9.1 VOC : 15 gr/L or 1.5 %
Caution Keep out of reach for children.
Keep from freezing.
a waterbased polish, ideal for smaller surfaces, table tops, windows sills, tresholds, work tops and counter tops.
Easy and quick to apply, and leaves a beautiful sheen. Also enhances the coulour and structures of stones.
Application Best suitable for smaller surfaces of marble, travertine, granite and other natural stones, as well as some synthetic surfaces.
Directions Ensure that the surface to be treated is clean and completely dry. Clean dirty surfaces with HG Marble Stripper.
Leave surface after cleaning to dry for up to 24 hours to avoid staining of the surface.
Apply thinly with lint-free cloth.
Allow the polish to dry for up to 30 minutes, before polishing with clean, dry and lint-free cloth, in circular motions, until a gloss appears.
Product Information s.g : 0.997 g/ml conteint : methylchloroisothiazolinone pH : 9.1 VOC : 15 gr/L or 1.5 %
Caution Keep out of reach for children.
Keep from freezing.