* Please Contact Us for Current Pricing!
Cement & Grout Film Removal
Marble & Stone Cement & Grout Release
to safely remove cement and grout residues, but also lime scale residues from natural stones.
Application specifically developed for calcareous natural stones like marble, travertine, limestone, terrazzo. Also safe and effective on granite and other stones.
Directions We suggest to have porous natural stones sealed with a penetrating sealer of your choice, prior to grouting, to avoid difficult to remove residues from grouting.
Read directions and precautions on label before starting.
Remove loose cement or grouting by sweeping or brushing with soft brush or by vacuuming.
Dilute Marble & Stone Cement & Lime at 1:10 ratio with warm water, and spread dilution over floor surface to be cleaned.
Allow to activate for 5-10 minutes then scrub with soft brush. Rinse with clean water, and preferably use wet-vacuum, or mop thoroughly to remove water and dirt.
Wall surfaces should be made wet with water, then HG be applied with soft brush, and applied from bottom up to prevent dripping.
Product Information s.g. : 1.05 gr/ml pH : approx. 9.5 usage : 30-40 m2 / 300-400 sq/ft per liter compositions : nonionics, sequestering agents
Caution Never use acids on calcareous natural stones, to avoid etching.
Wear goggles and rubber gloves.
Keep out of reach for children.
Keep from freezing. Do not ingest and avoid splashing in eyes.
Marble & Stone Cement & Grout Release
to safely remove cement and grout residues, but also lime scale residues from natural stones.
Application specifically developed for calcareous natural stones like marble, travertine, limestone, terrazzo. Also safe and effective on granite and other stones.
Directions We suggest to have porous natural stones sealed with a penetrating sealer of your choice, prior to grouting, to avoid difficult to remove residues from grouting.
Read directions and precautions on label before starting.
Remove loose cement or grouting by sweeping or brushing with soft brush or by vacuuming.
Dilute Marble & Stone Cement & Lime at 1:10 ratio with warm water, and spread dilution over floor surface to be cleaned.
Allow to activate for 5-10 minutes then scrub with soft brush. Rinse with clean water, and preferably use wet-vacuum, or mop thoroughly to remove water and dirt.
Wall surfaces should be made wet with water, then HG be applied with soft brush, and applied from bottom up to prevent dripping.
Product Information s.g. : 1.05 gr/ml pH : approx. 9.5 usage : 30-40 m2 / 300-400 sq/ft per liter compositions : nonionics, sequestering agents
Caution Never use acids on calcareous natural stones, to avoid etching.
Wear goggles and rubber gloves.
Keep out of reach for children.
Keep from freezing. Do not ingest and avoid splashing in eyes.
Floor Scrubber Brush
Synthetic bristles for safe scrubbing, and a squeegee to remove the loosened quickly and effectively.
Application Great for thorough cleaning on most floor surfaces, but also very effective in removing polishes and waxes as well as removal of cement and grout residues, in combination with suitable HG cleaner/stripper
Directions For easier working, apply the available 48" extention pole to the brush.
Dilute the selected HG cleaner or stripper
as directed. Scrub, rinse and use squeegee to wipe loosebed dirt and water from the surface.
Synthetic bristles for safe scrubbing, and a squeegee to remove the loosened quickly and effectively.
Application Great for thorough cleaning on most floor surfaces, but also very effective in removing polishes and waxes as well as removal of cement and grout residues, in combination with suitable HG cleaner/stripper
Directions For easier working, apply the available 48" extention pole to the brush.
Dilute the selected HG cleaner or stripper
as directed. Scrub, rinse and use squeegee to wipe loosebed dirt and water from the surface.
Daily Cleaner With Gloss
Marble & Stone Wash & Shine
A safe No-Rinse cleaner specifically developed for calcareous natural stones, like marble, travertine and terrazzo, to clean and leave a nice sheen and fresh scent in one go.
Application Suitable for all calcareous natural stones where extra sheen is required, like marble, travertine, limestone, terrazzo.
Directions Sweep surfaces to be cleaned, to remove dust, lint ansd hair.
Dilute 100ml./3 fl.oz Marble & Stone Wash and Shine with 5-6 liters of clean water.
Dip mop in dilution, wring out halfway, and mop surface. Rinse mop frequently in clean water to allow dirts to be disposed.
Continue mopping with dilution until finished. Leave surface to dry naturally to achive higher sheen.
Extremely dirty surfaces should be cleaned first with HG Marble Stripper.
Product Information s.g. : 1.03 gr/ml pH : approx. 8.5 components : nonionics<5%,preserving agent, perfume
Caution Keep out of reach for children.
Keep from freezing.
Marble & Stone Wash & Shine
A safe No-Rinse cleaner specifically developed for calcareous natural stones, like marble, travertine and terrazzo, to clean and leave a nice sheen and fresh scent in one go.
Application Suitable for all calcareous natural stones where extra sheen is required, like marble, travertine, limestone, terrazzo.
Directions Sweep surfaces to be cleaned, to remove dust, lint ansd hair.
Dilute 100ml./3 fl.oz Marble & Stone Wash and Shine with 5-6 liters of clean water.
Dip mop in dilution, wring out halfway, and mop surface. Rinse mop frequently in clean water to allow dirts to be disposed.
Continue mopping with dilution until finished. Leave surface to dry naturally to achive higher sheen.
Extremely dirty surfaces should be cleaned first with HG Marble Stripper.
Product Information s.g. : 1.03 gr/ml pH : approx. 8.5 components : nonionics<5%,preserving agent, perfume
Caution Keep out of reach for children.
Keep from freezing.
Marble & Stone Floor Soap
A safe cleaner for regular use, specifically developed for calcareous natural stone floors, that while cleaning, enhances the colour en veining.
Suitable for use by hand or cleaning machine.
Application Safe and suitable for use on all calcareous natural stone floors, like marble, limestone, travertine, terrazzo, but also slate surfaces pre-treated with penetrating sealers.
Directions Sweep floors, before cleaning with HG Marble & Stone Floor Soap.
Dilute 200-300 ml.with up to 10 liters of clean cold or warm water.
Apply with halfway wrung mop.Do NOT rinse, but leave to dry naturally.
To achive higher gloss, buff slightly.
Severely soiled surfaces should be cleaned first with HG Marble & Stone Stripper.
Product Information name : Environmentally friendly / Biodegradable s.g. : 1.015 gr/ml pH : 9 compositions : nonionics<5%,soap 5-15%, perfume active matter : 19%
Caution Keep out of reach for children.
Keep from freezing.
A safe cleaner for regular use, specifically developed for calcareous natural stone floors, that while cleaning, enhances the colour en veining.
Suitable for use by hand or cleaning machine.
Application Safe and suitable for use on all calcareous natural stone floors, like marble, limestone, travertine, terrazzo, but also slate surfaces pre-treated with penetrating sealers.
Directions Sweep floors, before cleaning with HG Marble & Stone Floor Soap.
Dilute 200-300 ml.with up to 10 liters of clean cold or warm water.
Apply with halfway wrung mop.Do NOT rinse, but leave to dry naturally.
To achive higher gloss, buff slightly.
Severely soiled surfaces should be cleaned first with HG Marble & Stone Stripper.
Product Information name : Environmentally friendly / Biodegradable s.g. : 1.015 gr/ml pH : 9 compositions : nonionics<5%,soap 5-15%, perfume active matter : 19%
Caution Keep out of reach for children.
Keep from freezing.
Daily Cleaner Without Gloss
Marble & Stone Neutral Cleaner
A safe pH neutral cleaner specifically developed for regular use on vulnerable natural stones, like marble, travertine, limestone, terrazzo, granite, quartzite, slate.
Low foaming, therefore suitable for machine use. NO-RINSE formula.
HG Marble Neutral Cleaner will not attack sealers and polishes.
Application On all treated (sealed, polished and/or waxed) as well as untreated marbles, travertines, terrazzo, limestone, granite and other natural stones, like slate, quartzite, even ceramics.
Directions First remove loose dirts, by sweeping or vacuming.
Dilute HG Marble Neutral Cleaner with lukewarm water, at a
ratio of: 1:120 for lightly soiled surfaces, or up to 1:64 for severly soiled surfaces. Mop the surface thoroughly. Rinse mop frequently to avoid carrying dirts from one to another spot. There is no need to rinse mopped areas.
Severely soiled areas, might scrubbing and a repeat treatment.
Is it advantages to use a wet-vacuum cleaner.
Product Information s.g. : 1.005 g/ml pH : 7.5-8.0 compositions : non-ionics,phosphonates,perfumes.
Caution Store in frost-free area.
Keep out of reach for children. In case of eye contact, rinse with clean water, and consult phycisian.
In case of swallowing, drink plenty of water and call phycisian.
Marble & Stone Neutral Cleaner
A safe pH neutral cleaner specifically developed for regular use on vulnerable natural stones, like marble, travertine, limestone, terrazzo, granite, quartzite, slate.
Low foaming, therefore suitable for machine use. NO-RINSE formula.
HG Marble Neutral Cleaner will not attack sealers and polishes.
Application On all treated (sealed, polished and/or waxed) as well as untreated marbles, travertines, terrazzo, limestone, granite and other natural stones, like slate, quartzite, even ceramics.
Directions First remove loose dirts, by sweeping or vacuming.
Dilute HG Marble Neutral Cleaner with lukewarm water, at a
ratio of: 1:120 for lightly soiled surfaces, or up to 1:64 for severly soiled surfaces. Mop the surface thoroughly. Rinse mop frequently to avoid carrying dirts from one to another spot. There is no need to rinse mopped areas.
Severely soiled areas, might scrubbing and a repeat treatment.
Is it advantages to use a wet-vacuum cleaner.
Product Information s.g. : 1.005 g/ml pH : 7.5-8.0 compositions : non-ionics,phosphonates,perfumes.
Caution Store in frost-free area.
Keep out of reach for children. In case of eye contact, rinse with clean water, and consult phycisian.
In case of swallowing, drink plenty of water and call phycisian.
Penetrating Sealer - Colour Enhancing
Colour Enhancing (penetrating) Sealer
Low Vapour Pressure, VOC compliant stain blocking,protective penetrating sealer that enhances the colour and appearance of porous natural stones,without adding gloss and without making the surface slippery. Suitable for interior and exterior use, as it allows the surface to breath naturally. The effect of Color Enhancer comes out better as the colour of the stone is darker.
LONGLASTING result. NO silicones.
Use HG Streak-Free Cleaner for regular maintenance indoors.
If artificial gloss was applied use HG Superfloor for regular maintenance, indoors.
Application Porous natural stones, such as slate, Flagstones, Limestone, Travertine, Tumbled Marble. etc.
Directions The surface to be treated should be dry, clean and free from dust.
Before applying the product, ensure all of the above.
Apply the product in a thin layer by using a paintbrush or roller.
Allow to dry fro 8 to 15 minutes before removing residue. If necessary apply a second coat.
Do NOT use on sealed, glazed, polished or non-absorbtive surfaces. Allow good ventilation.
Apply only as much sealer as the surface can absorp. If overapplied, remove with lintfree cloth or old towel, or use squeegee to move overdose to untreated parts of the surface.
If overdose was left to dry, only a paintstripper with diclormethane (DCM) can be used to remove residue. (available at your local paintstore)
Product Information s.g. : n/a pH : n/a compositions : Petroleum Distillate plus Proprietary Oil Usage : from 200-400 sq/ft per liter, depending, absorption. other : Colourless, transparant liquid. Flammable liquid & fumes.
Caution Flammable.
Keep out of reach for children.
Colour Enhancing (penetrating) Sealer
Low Vapour Pressure, VOC compliant stain blocking,protective penetrating sealer that enhances the colour and appearance of porous natural stones,without adding gloss and without making the surface slippery. Suitable for interior and exterior use, as it allows the surface to breath naturally. The effect of Color Enhancer comes out better as the colour of the stone is darker.
LONGLASTING result. NO silicones.
Use HG Streak-Free Cleaner for regular maintenance indoors.
If artificial gloss was applied use HG Superfloor for regular maintenance, indoors.
Application Porous natural stones, such as slate, Flagstones, Limestone, Travertine, Tumbled Marble. etc.
Directions The surface to be treated should be dry, clean and free from dust.
Before applying the product, ensure all of the above.
Apply the product in a thin layer by using a paintbrush or roller.
Allow to dry fro 8 to 15 minutes before removing residue. If necessary apply a second coat.
Do NOT use on sealed, glazed, polished or non-absorbtive surfaces. Allow good ventilation.
Apply only as much sealer as the surface can absorp. If overapplied, remove with lintfree cloth or old towel, or use squeegee to move overdose to untreated parts of the surface.
If overdose was left to dry, only a paintstripper with diclormethane (DCM) can be used to remove residue. (available at your local paintstore)
Product Information s.g. : n/a pH : n/a compositions : Petroleum Distillate plus Proprietary Oil Usage : from 200-400 sq/ft per liter, depending, absorption. other : Colourless, transparant liquid. Flammable liquid & fumes.
Caution Flammable.
Keep out of reach for children.
Penetrating Sealer - invisible
DEFENDER protective sealer, solventbased.
Virtually invisible protective penetrating sealer to block stains and dirt, without changing the colour and gloss.
LVP-VOC compliant, solvent based sealer, for interior and exterior use.
Application Suitable for all natural stones, pavers, brick, even concrete surfaces.
Directions Shake can well before use. Wear goggles & rubber gloves, and ensure adequate ventilation. Protect surfaces NOT to be treated. Ensure that surface to be treated are clean and completely dry.
Smaller area: pour some sealer on lintfree cloth and wipe over surface to be treated. Allow to penetrate for 10-15 minutes before wiping up any puddles or surplus.
Allow to dry for 2 hours before applying a second coat, following same instructions.
Larger areas: pour sealer in paint tray and apply thin coat of sealer with hair (not foam) roller, in one direction. After 10-15 minutes remove any puddles or surplus with lintfree cloth or squeegee.
Allow to dry for 2 hours before applying a second following same directions.
After final coat, allow to dry minimum 4 hours before walking, and minimum 12 hours before heavier traffic.
Product Information s.g. : 0.88 compositions : petroleum distillate & blend of proprietary polymers. usage : 200-400 sq/ft per litre.
Caution Combustible liquid. Wear goggles and rubber gloves. Ensure adequate ventilation.
Do not MIX or match with other products to avoid result differences. Best working temperature are between 15-25C / 55-75F, low humidity and never in full sun.
Avoid dust and dirt while drying. For outside applications, ensure sprinkler systems to be shut off, and avoid any moisture and rain during drying process.
DEFENDER protective sealer, solventbased.
Virtually invisible protective penetrating sealer to block stains and dirt, without changing the colour and gloss.
LVP-VOC compliant, solvent based sealer, for interior and exterior use.
Application Suitable for all natural stones, pavers, brick, even concrete surfaces.
Directions Shake can well before use. Wear goggles & rubber gloves, and ensure adequate ventilation. Protect surfaces NOT to be treated. Ensure that surface to be treated are clean and completely dry.
Smaller area: pour some sealer on lintfree cloth and wipe over surface to be treated. Allow to penetrate for 10-15 minutes before wiping up any puddles or surplus.
Allow to dry for 2 hours before applying a second coat, following same instructions.
Larger areas: pour sealer in paint tray and apply thin coat of sealer with hair (not foam) roller, in one direction. After 10-15 minutes remove any puddles or surplus with lintfree cloth or squeegee.
Allow to dry for 2 hours before applying a second following same directions.
After final coat, allow to dry minimum 4 hours before walking, and minimum 12 hours before heavier traffic.
Product Information s.g. : 0.88 compositions : petroleum distillate & blend of proprietary polymers. usage : 200-400 sq/ft per litre.
Caution Combustible liquid. Wear goggles and rubber gloves. Ensure adequate ventilation.
Do not MIX or match with other products to avoid result differences. Best working temperature are between 15-25C / 55-75F, low humidity and never in full sun.
Avoid dust and dirt while drying. For outside applications, ensure sprinkler systems to be shut off, and avoid any moisture and rain during drying process.
Stain Removal
Marble & Stone Rust & Oxidation Remover
To remove rust and oxidation stains from marble, concrete, slate but also from wood.
Non-acid formula. Extremely effective.
Application marble, concrete, slate but also from wood.
Directions Use on dry surface, and temperatures above 15C. Shake bottle before use. Ensure proper ventilation as the product smells. Ensure that liquid and dirt run-off does not drip on other surfaces. Protect surfaces not to be treated.
Spray product completely over the stained area and leave to activate for approx. 5 and up to 15 minutes, but prevent the liquid from drying. Rust stains might show a purple colour after spraying, use clean cloth or paper to have these stains absorbed immediately.
Afterwards rinse well. Possible discolouring from treatment.
Stains might need second treatments.
Product Information pH : 7 - 9 Relative Density : 1.05 Odour : Rotten eggs
Caution Keep out of reach for children.
Harmful if swallowed or inhaled.
Read complete directions for use.
Keep from freezing.
Marble & Stone Rust & Oxidation Remover
To remove rust and oxidation stains from marble, concrete, slate but also from wood.
Non-acid formula. Extremely effective.
Application marble, concrete, slate but also from wood.
Directions Use on dry surface, and temperatures above 15C. Shake bottle before use. Ensure proper ventilation as the product smells. Ensure that liquid and dirt run-off does not drip on other surfaces. Protect surfaces not to be treated.
Spray product completely over the stained area and leave to activate for approx. 5 and up to 15 minutes, but prevent the liquid from drying. Rust stains might show a purple colour after spraying, use clean cloth or paper to have these stains absorbed immediately.
Afterwards rinse well. Possible discolouring from treatment.
Stains might need second treatments.
Product Information pH : 7 - 9 Relative Density : 1.05 Odour : Rotten eggs
Caution Keep out of reach for children.
Harmful if swallowed or inhaled.
Read complete directions for use.
Keep from freezing.
Oil & Grease Absorber
Cleaning poultice, that removes virtually all type of oil grease and fat stains and blemishes.
Is self-acting. No scrubbing required.
Application Suitable on all porous tiles and stone surfaces, such as ceramic, terra cotta, marble, limestone, slate, as well as cement and concrete surfaces.
Directions Stir the HG Oil & Grease Stain Absorber well before use.
Use spatula, spoon or knife to apply an approx.1/4" thick coating to the stain, from the edges of the stain to the centre.
Wait a minimum of 1 hour or 2, until product has dried to a hard white crust before removing. Repeat if necessary.
Attention: the product might remove protective coatings.
Product Information s.g. : 0.87 gr/ml. composition : aliphatic hydrocarbons, methylal, dioxolan, silicates. Other : Beige paste, with odour.
Caution Keep out of reach for children. Highly flammable.
Irritating to eye, respiratory systems and skin.
Keep away from source of ignition. No smoking.
If swallowed, seek medical advise immediately and show container or label.
Cleaning poultice, that removes virtually all type of oil grease and fat stains and blemishes.
Is self-acting. No scrubbing required.
Application Suitable on all porous tiles and stone surfaces, such as ceramic, terra cotta, marble, limestone, slate, as well as cement and concrete surfaces.
Directions Stir the HG Oil & Grease Stain Absorber well before use.
Use spatula, spoon or knife to apply an approx.1/4" thick coating to the stain, from the edges of the stain to the centre.
Wait a minimum of 1 hour or 2, until product has dried to a hard white crust before removing. Repeat if necessary.
Attention: the product might remove protective coatings.
Product Information s.g. : 0.87 gr/ml. composition : aliphatic hydrocarbons, methylal, dioxolan, silicates. Other : Beige paste, with odour.
Caution Keep out of reach for children. Highly flammable.
Irritating to eye, respiratory systems and skin.
Keep away from source of ignition. No smoking.
If swallowed, seek medical advise immediately and show container or label.
SpotStain Remover
A concentrated, self-acting solvent cleaner, that removes virtually all type of oil grease and fat stains and blemishes, and to remove residues from impregnating sealers and epoxy grout residue.
Application Suitable on all porous tiles and stone surfaces, ceramic, terra cotta, marble, limestone, slate, as well as cement and concrete surfaces. In some cases even suitable on carpets.
Directions Shake bottle before use. Apply concentrated where necessary.
Otherwise, dilute up 1:3 with clean water. Apply over the surface to be cleaned and leave to activate for 5-10 minutes.
surface to be cleaned and leave to activate for 5-10 minutes.
Repeat if necessary.
Attention: the product might remove protective coatings.
Product Information pH : 8.7 s.g. : 0.95 gr/ml. composition : aromatic hydrocarbon, emulgator, alcohol detergents. odour : Milky liquid, with odour.
Caution Keep out of reach for children. Highly flammable.
Irritating to eye, respiratory systems and skin.
Keep away from source of ignition. No smoking.
If swallowed, seek medical advise immediately and show container or label.
A concentrated, self-acting solvent cleaner, that removes virtually all type of oil grease and fat stains and blemishes, and to remove residues from impregnating sealers and epoxy grout residue.
Application Suitable on all porous tiles and stone surfaces, ceramic, terra cotta, marble, limestone, slate, as well as cement and concrete surfaces. In some cases even suitable on carpets.
Directions Shake bottle before use. Apply concentrated where necessary.
Otherwise, dilute up 1:3 with clean water. Apply over the surface to be cleaned and leave to activate for 5-10 minutes.
surface to be cleaned and leave to activate for 5-10 minutes.
Repeat if necessary.
Attention: the product might remove protective coatings.
Product Information pH : 8.7 s.g. : 0.95 gr/ml. composition : aromatic hydrocarbon, emulgator, alcohol detergents. odour : Milky liquid, with odour.
Caution Keep out of reach for children. Highly flammable.
Irritating to eye, respiratory systems and skin.
Keep away from source of ignition. No smoking.
If swallowed, seek medical advise immediately and show container or label.
Marble Stain Colour Remover
A concentrated alkaline cleaning agent to remove stains in calcareous stones, by attacking the dye that the stain consist of, like the brown of a coffee stain, the red from a wine stain, etc.
This product is not able to fix etch marks that often occur when surfaces are stained with juices, acids, vinegar, nail polish remover, etc. (see Natural Stone Restoration)
Application Suitable for use on all calcareous natural stones, like marble, travertine, limestone, sandstone, terrazzo.
Directions When a died stain occurs, do not try to remove with unsuitable cleaners, as they will transport the stain down further into the surface, making it often impossible to remove.
Spray liquid from 3-5 cm / 2-3" over stained area and leave to activate for 30 minutes, before mopping up. Repeat if necessary.
When successful, we suggest cleaning the complete area with HG Marble & Stone Stripper, and subsequently protecting the surface with a suitable penetrating sealer to avoid future staining.
Product Information compositions : sodium percarbonate>60% physical state : odourless powder s.g. : approx. 1 gr/ml pH : 10 VOC % : none
Caution Beware of bleaching splashing. Protect areas not be treated. Store in cool and dark place. Keep seperate from flammables.
Follow directions carefully.
Keep out of reach for children.
A concentrated alkaline cleaning agent to remove stains in calcareous stones, by attacking the dye that the stain consist of, like the brown of a coffee stain, the red from a wine stain, etc.
This product is not able to fix etch marks that often occur when surfaces are stained with juices, acids, vinegar, nail polish remover, etc. (see Natural Stone Restoration)
Application Suitable for use on all calcareous natural stones, like marble, travertine, limestone, sandstone, terrazzo.
Directions When a died stain occurs, do not try to remove with unsuitable cleaners, as they will transport the stain down further into the surface, making it often impossible to remove.
Spray liquid from 3-5 cm / 2-3" over stained area and leave to activate for 30 minutes, before mopping up. Repeat if necessary.
When successful, we suggest cleaning the complete area with HG Marble & Stone Stripper, and subsequently protecting the surface with a suitable penetrating sealer to avoid future staining.
Product Information compositions : sodium percarbonate>60% physical state : odourless powder s.g. : approx. 1 gr/ml pH : 10 VOC % : none
Caution Beware of bleaching splashing. Protect areas not be treated. Store in cool and dark place. Keep seperate from flammables.
Follow directions carefully.
Keep out of reach for children.
Thorough Cleaner/Stripper
Marble & Stone Stripper
An intensive cleaner to remove polishes and waxes as well as stubborn dirt and fats. Does not affect the natural gloss from the surface.
Application suitable for all marble, travertin, limestone, terrazzo and granite.
Directions to remove polishes and waxes, use undiluted. For thorough cleaning dilute 1:3 with clean lukewarm water.(1 litre HG with 3 liters of water.
Product Information
Caution Keep out of reach of children.
Marble & Stone Stripper
An intensive cleaner to remove polishes and waxes as well as stubborn dirt and fats. Does not affect the natural gloss from the surface.
Application suitable for all marble, travertin, limestone, terrazzo and granite.
Directions to remove polishes and waxes, use undiluted. For thorough cleaning dilute 1:3 with clean lukewarm water.(1 litre HG with 3 liters of water.
Product Information
Caution Keep out of reach of children.
Topical Protection
Marble & Stone Shine Finish
a waterbased, metal-linked, acrylic polymer protective polish topcoat, for interior use only.
Excellent extra protection overtop penetrating sealers, that adds topical gloss, enhances colour and prevents staining. Selfshining and anti-slip.
Application Suitable on all and any calcareous natural stone that requires extra gloss, like dullish marbles, travertines, limestone and terrazzo. Do NOT apply on granite, nor on any other surfaces in outdoor applications.
Directions Ensure that surfaces are clean, dry and free from dirt and dust
Do NOT stir or shake bottle to avoid foaming. Apply thinly with wax applicator or lintfree cloth. Allow to dry for 45 min. before applying a second coat at right angles.
Wear areas and tracks may be treated seperately when necessary, without stripping, but ensuring that surface is clean. After 10 to 12 applications we suggest to strip surface with HG Marble & Stone Stripper, and start procedure over.
To achieve higher gloss, each layer applied may be buffed with white pad and high speed buffer.
Regular maintenance with HG Marble Wash & Shine
Product Information s.g. : 1.02 gr/ml pH : approx. 8.5 usage : 60-70m2 / 600-750 sq/ft per liter, depending absorption compositions : acrylic emulsions,glycols, plastizers,levelling agents VOC : 55 gr/L or 5.5%
Caution Keep out of reach for children.
Keep from freezing.
Do NOT apply over surfaces treated with HG Marble & Stone Protector (art.204)
Marble & Stone Shine Finish
a waterbased, metal-linked, acrylic polymer protective polish topcoat, for interior use only.
Excellent extra protection overtop penetrating sealers, that adds topical gloss, enhances colour and prevents staining. Selfshining and anti-slip.
Application Suitable on all and any calcareous natural stone that requires extra gloss, like dullish marbles, travertines, limestone and terrazzo. Do NOT apply on granite, nor on any other surfaces in outdoor applications.
Directions Ensure that surfaces are clean, dry and free from dirt and dust
Do NOT stir or shake bottle to avoid foaming. Apply thinly with wax applicator or lintfree cloth. Allow to dry for 45 min. before applying a second coat at right angles.
Wear areas and tracks may be treated seperately when necessary, without stripping, but ensuring that surface is clean. After 10 to 12 applications we suggest to strip surface with HG Marble & Stone Stripper, and start procedure over.
To achieve higher gloss, each layer applied may be buffed with white pad and high speed buffer.
Regular maintenance with HG Marble Wash & Shine
Product Information s.g. : 1.02 gr/ml pH : approx. 8.5 usage : 60-70m2 / 600-750 sq/ft per liter, depending absorption compositions : acrylic emulsions,glycols, plastizers,levelling agents VOC : 55 gr/L or 5.5%
Caution Keep out of reach for children.
Keep from freezing.
Do NOT apply over surfaces treated with HG Marble & Stone Protector (art.204)
Lambswool Sealer Applicator Block
Synthetic lambswool block for easy and thin applications of impregnating and surface sealers on absorptive surfaces.
Application Suitable for use with solvent(oil)based, waterbased sealers, but also polish and wax applications.
Directions pour a portion of the selected HG sealer into the tray. Soak the applicator in the sealer or polish, and press out any excess quantity. Follow directions as per selected product label.
Synthetic lambswool block for easy and thin applications of impregnating and surface sealers on absorptive surfaces.
Application Suitable for use with solvent(oil)based, waterbased sealers, but also polish and wax applications.
Directions pour a portion of the selected HG sealer into the tray. Soak the applicator in the sealer or polish, and press out any excess quantity. Follow directions as per selected product label.
Impregnating Sealer
DEFENDER protective sealer, solventbased.
Virtually invisible protective penetrating sealer to block stains and dirt, without changing the colour and gloss.
LVP-VOC compliant, solvent based sealer, for interior and exterior use.
Application Suitable for all natural stones, pavers, brick, even concrete surfaces.
Directions Shake can well before use. Wear goggles & rubber gloves, and ensure adequate ventilation. Protect surfaces NOT to be treated. Ensure that surface to be treated are clean and completely dry.
Smaller area: pour some sealer on lintfree cloth and wipe over surface to be treated. Allow to penetrate for 10-15 minutes before wiping up any puddles or surplus.
Allow to dry for 2 hours before applying a second coat, following same instructions.
Larger areas: pour sealer in paint tray and apply thin coat of sealer with hair (not foam) roller, in one direction. After 10-15 minutes remove any puddles or surplus with lintfree cloth or squeegee.
Allow to dry for 2 hours before applying a second following same directions.
After final coat, allow to dry minimum 4 hours before walking, and minimum 12 hours before heavier traffic.
Product Information s.g. : 0.88 compositions : petroleum distillate & blend of proprietary polymers. usage : 200-400 sq/ft per litre.
Caution Combustible liquid. Wear goggles and rubber gloves. Ensure adequate ventilation.
Do not MIX or match with other products to avoid result differences. Best working temperature are between 15-25C / 55-75F, low humidity and never in full sun.
Avoid dust and dirt while drying. For outside applications, ensure sprinkler systems to be shut off, and avoid any moisture and rain during drying process.
DEFENDER protective sealer, solventbased.
Virtually invisible protective penetrating sealer to block stains and dirt, without changing the colour and gloss.
LVP-VOC compliant, solvent based sealer, for interior and exterior use.
Application Suitable for all natural stones, pavers, brick, even concrete surfaces.
Directions Shake can well before use. Wear goggles & rubber gloves, and ensure adequate ventilation. Protect surfaces NOT to be treated. Ensure that surface to be treated are clean and completely dry.
Smaller area: pour some sealer on lintfree cloth and wipe over surface to be treated. Allow to penetrate for 10-15 minutes before wiping up any puddles or surplus.
Allow to dry for 2 hours before applying a second coat, following same instructions.
Larger areas: pour sealer in paint tray and apply thin coat of sealer with hair (not foam) roller, in one direction. After 10-15 minutes remove any puddles or surplus with lintfree cloth or squeegee.
Allow to dry for 2 hours before applying a second following same directions.
After final coat, allow to dry minimum 4 hours before walking, and minimum 12 hours before heavier traffic.
Product Information s.g. : 0.88 compositions : petroleum distillate & blend of proprietary polymers. usage : 200-400 sq/ft per litre.
Caution Combustible liquid. Wear goggles and rubber gloves. Ensure adequate ventilation.
Do not MIX or match with other products to avoid result differences. Best working temperature are between 15-25C / 55-75F, low humidity and never in full sun.
Avoid dust and dirt while drying. For outside applications, ensure sprinkler systems to be shut off, and avoid any moisture and rain during drying process.
Stone & Marble Penetrating Sealer
- Waterbased/ VOC FREE
A waterbased, VOC-FREE, and completely invisible basic sealer to protect surfaces from staining.
Suitable for in- and exteriors surfaces, both horizontal and vertical.
ATTENTION: This waterbased product may NOT be mixed with other and/or solventbased penetrating sealers. To avoid possible colour differences, do NOT use this product adjacent other penetrating sealers. This product may be used overtop fully dried solventbased penetrating sealers, to further protect from dirt.
Application Suitable for use on most marbles and other honed stones, as well as limestone, travertine, slate, quarry tile, terra cotta, even concrete and full-body porcelain tiles.
Directions ensure that surfaces are clean and completely dry. New installation should be allowed to cure (dry) for possibly a weeks before sealing. Cleaned surfaces require a minimum of 24 hour drying.
Depending the size of job, use a lintfree cloth on small jobs, a mohair roller or wax applicator for larger jobs, even low-pressure spraying for large jobs.
Apply sealer in thin coat in one direction.
On less absorptive surfaces, remove any possible surplus of the sealer within 10 minutes with clean cloth. On larger jobs move surplus with squeegee over to untreated parts of the surface.
Do NOT treat areas large than can be handled to avoid a build up from surplus.
If after approx. 10 minutes there is no surplus, and all material has been absorbed into the surface, allow 1 hour drying before applying a subsequent coat of sealer. Allow final coat to dry for 3 hours before light foor traffic, and at least 24 hours before regular traffic and or liquid spills or cleaning.
Product Information coverage : 10-20 m2 / 100-200 sq/ft per litre on highly porous surfaces Rendement : 20-50 m2 / 200 - 500 sq/ft per litre on lesser porous surfaces
Caution Keep out of reach for children.
Keep from freezing.
If swallowed, call a poison control centre or doctor immediately. Do NOT induce vomiting.
- Waterbased/ VOC FREE
A waterbased, VOC-FREE, and completely invisible basic sealer to protect surfaces from staining.
Suitable for in- and exteriors surfaces, both horizontal and vertical.
ATTENTION: This waterbased product may NOT be mixed with other and/or solventbased penetrating sealers. To avoid possible colour differences, do NOT use this product adjacent other penetrating sealers. This product may be used overtop fully dried solventbased penetrating sealers, to further protect from dirt.
Application Suitable for use on most marbles and other honed stones, as well as limestone, travertine, slate, quarry tile, terra cotta, even concrete and full-body porcelain tiles.
Directions ensure that surfaces are clean and completely dry. New installation should be allowed to cure (dry) for possibly a weeks before sealing. Cleaned surfaces require a minimum of 24 hour drying.
Depending the size of job, use a lintfree cloth on small jobs, a mohair roller or wax applicator for larger jobs, even low-pressure spraying for large jobs.
Apply sealer in thin coat in one direction.
On less absorptive surfaces, remove any possible surplus of the sealer within 10 minutes with clean cloth. On larger jobs move surplus with squeegee over to untreated parts of the surface.
Do NOT treat areas large than can be handled to avoid a build up from surplus.
If after approx. 10 minutes there is no surplus, and all material has been absorbed into the surface, allow 1 hour drying before applying a subsequent coat of sealer. Allow final coat to dry for 3 hours before light foor traffic, and at least 24 hours before regular traffic and or liquid spills or cleaning.
Product Information coverage : 10-20 m2 / 100-200 sq/ft per litre on highly porous surfaces Rendement : 20-50 m2 / 200 - 500 sq/ft per litre on lesser porous surfaces
Caution Keep out of reach for children.
Keep from freezing.
If swallowed, call a poison control centre or doctor immediately. Do NOT induce vomiting.